What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Sections
SKIL TS6307-00 Table Saw Review: Specs, Setup, and Value
The SKIL TS6307-00 table saw is a strong-value choice for homeowners and occasional DIYers who need a portable 10-inch saw with a folding stand, but its jobsite-style design is better suited to sheet-goods breakdown and general project work than to a permanently installed, precision-focused shop.
Its main appeal is a useful mix of capacity and manageable setup: the fence extends the rip width to 25½ inches, and the included folding stand avoids the extra cost and storage needs of a separate base. Before buying, weigh those benefits against the saw’s roughly 51-pound weight, limited dust collection, and the adjustment checks any portable saw needs before accurate work.
As an Amazon Associate we earn from qualifying purchases at no extra cost to you.
SKIL TS6307-00 specifications at a glance
| Specification | SKIL TS6307-00 | What it means in use |
|---|---|---|
| Blade diameter | 10 inches | Uses a common blade size, with a broad selection of replacement and specialty blades. |
| Arbor | 5/8 inch | Check the arbor hole when choosing a compatible blade. |
| Motor | 15 amps | Standard corded-saw power; it does not require batteries, but does need a suitable outlet and extension cord if used outdoors. |
| No-load speed | 5,000 rpm | Blade speed is fixed; feed rate and blade choice matter for clean cuts. |
| Maximum rip capacity | 25½ inches | Enough for ripping a 4-by-8-foot sheet lengthwise when the work is supported properly. |
| Maximum depth of cut at 90° | 3½ inches | Can cut through standard 4-by-4 stock in one pass, subject to the material and safe setup. |
| Maximum depth of cut at 45° | 2½ inches | Allows substantial bevel cuts, though capacity falls as the blade tilts. |
| Approximate assembled weight | About 51 pounds | Portable by one person for short moves, but not especially light to carry repeatedly. |
These figures explain why searches for “skil table saw ts6307-00,” “ts6307 00 skil 10 in table saw,” “ts6307-00 skil 10 in. table saw,” and “skilsaw table saw ts6307-00” often lead to the same buying question: is this a genuinely capable portable saw, or merely a compact compromise? Its rip capacity is useful for common panel work, while the 3½-inch depth at 90 degrees handles many framing and furniture cuts. The limitation is not the headline capacity so much as supporting large stock safely and keeping the saw aligned over time.
Cutting capacity: practical, with a support caveat
A 25½-inch rip capacity gives the TS6307-00 room to rip the long dimension of a standard 48-inch-wide plywood or OSB sheet, with the fence extended. That does not make a full sheet easy to handle on the saw alone. Large panels can tip, bind, or pull away from the fence if unsupported. Use a stable outfeed surface and arrange help or a panel-handling method for bulky stock; never reach across the blade to catch a falling offcut.
The saw’s 3½-inch maximum cut depth at 90 degrees is useful for many common jobs, including cutting 2-by lumber and, in principle, 4-by material. Capacity is not a promise that every thick or dense piece should be cut in one pass. Check the blade condition, keep the stock flat against the table, and use a controlled feed. For repeatable bevel or crosscuts, a suitable miter gauge or sled can help, but the included fence is meant for ripping—not for guiding crosscuts.
Fence and folding stand: what to check during setup
The rack-and-pinion fence adjustment is one of the saw’s most practical features. Rather than dragging the fence into position by hand, the mechanism moves it in a controlled way and helps keep front and rear ends aligned as the setting changes. That makes width adjustments easier, particularly when switching between narrow and wider rips.
Still, a fence mechanism does not remove the need to verify accuracy. After assembling the saw, unplug it and check that the fence is parallel to the blade using a reliable measuring method. Also check that the blade is square to the table at 90 degrees and that the miter gauge sits correctly in its slot. If a cut burns, wanders, or pinches, stop and investigate alignment, blade sharpness, and stock support rather than forcing the work through.
The included folding stand saves floor space and makes storage more convenient than a fixed cabinet base. Set it on firm, level ground, fully engage its locking points, and check for rocking before cutting. The stand is a setup aid, not a substitute for a stable work area: uneven pavement or a loose latch can make feeding long stock harder and less safe. Allow enough clearance around the saw to control both the infeed and outfeed sides.
Portability and ownership realities
At about 51 pounds, the TS6307-00 is portable in the sense that one person can reposition or load it, but it is not a lightweight grab-and-go tool. The folding stand helps with storage and deployment; it does not eliminate the effort of carrying the saw through a house, lifting it into a vehicle, or moving it over stairs. If you will transport it often, consider where it will be stored and how it will be lifted before deciding that a folding design alone solves portability.
Dust collection is another workshop consideration. A vacuum connection can reduce the amount of debris left around the saw, but a compact jobsite setup is not equivalent to a fully enclosed cabinet with a dedicated dust collector. Expect to sweep up, especially when cutting sheet goods. Keep the motor vents and adjustment mechanisms clear of dust, and unplug the saw before cleaning or making adjustments.
The first items likely to affect cut quality are the blade and alignment, not necessarily the motor. A dull or unsuitable blade can leave rough edges, increase burning, and make feeding more difficult. Keep the blade clean, inspect it for damage, and choose a tooth configuration suited to the material and finish you need. Store the fence and accessories so they do not get knocked out of adjustment, and periodically recheck alignment if the saw has been moved or transported.
Who should buy it?
| Your situation | Fit | Why |
|---|---|---|
| DIYer with limited storage | Good fit | The folding stand stores more compactly than a permanent cabinet saw and is included in the package. |
| Occasional remodel or home project work | Good fit | Its 25½-inch rip capacity and 3½-inch cut depth cover many common cuts without shop-scale space. |
| Frequent transport between jobs | Conditional fit | The stand folds, but the roughly 51-pound assembly still takes effort to carry and load. |
| Beginner seeking an easy first table saw | Reasonable fit with setup time | The fence adjustment is convenient, but safe use still requires alignment checks, push sticks, and proper stock support. |
| Cabinetmaker needing repeatable shop precision | Look at a heavier shop saw | A fixed, more substantial saw and a dedicated outfeed setup are better suited to frequent precision work. |
Is the price justified?
Prices vary by retailer and season, but the TS6307-00 generally sits in the value-oriented portable-saw category, with market pricing commonly in the low-to-mid hundreds of dollars. Its value is strongest when you need the saw and folding stand together: you get a full-size 10-inch blade, useful rip capacity, and a fence system designed for easier adjustment without having to build a permanent base.
Compare the total setup cost, not just the saw price. You may also need a suitable blade, push sticks, eye and hearing protection, dust collection, and an outfeed support solution. If you already own a stable stand and need a lighter saw to move around, the included stand may be less valuable to you. If the saw will live in a compact garage and come out for weekend projects, the bundled setup is easier to justify.
Verdict
The SKIL TS6307-00 is a capable portable table saw for homeowners and DIYers who prioritize usable cutting capacity, a convenient fence, and a folding stand at a moderate price. Its real-world portability is good for storage and occasional repositioning, not effortless daily hauling. Buy it if that balance matches your work; choose a heavier shop saw for frequent precision production, or a lighter setup if carrying weight matters more than the included stand and 25½-inch rip capacity.