Key takeaways
- Compare the best joist hangers for decks and framing, from galvanized singles for 2x6 joists to stainless and double hangers built for doubled 2x8 members.
What's inside
- Quick Answer
- How to Read the LUS Model Number
- Simpson Strong-Tie LUS26Z ZMAX Joist Hanger, 50-Pack
- Simpson Strong-Tie LUS26-2 Double Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS26 Galvanized Joist Hanger, 100-Pack
- Simpson Strong-Tie LUS28SS Stainless Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS28-2 Double Joist Hanger, 25-Pack
- How to Choose
- Who Should Skip
- Frequently Asked Questions
- Final Verdict
- Product and ASIN Reference
- Quick Answer
- How to Read the LUS Model Number
- Simpson Strong-Tie LUS26Z ZMAX Joist Hanger, 50-Pack
- Simpson Strong-Tie LUS26-2 Double Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS26 Galvanized Joist Hanger, 100-Pack
- Simpson Strong-Tie LUS28SS Stainless Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS28-2 Double Joist Hanger, 25-Pack
- How to Choose
- Who Should Skip
- Frequently Asked Questions
- Final Verdict
- Product and ASIN Reference
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Equipment › Best Joist Hangers for Solid Decks and Sturdy Frame Joints
A deck that feels firm underfoot owes most of its quiet confidence to hardware nobody sees. Joist hangers carry the end of every joist, tie it to the ledger or beam, and keep the frame square through seasons of swelling and foot traffic. A hanger that fits its lumber, matches its environment, and gets every nail hole filled will outlast the deck boards it supports.
This guide compares five Simpson Strong-Tie LUS face-mount hangers, the workhorse family for solid-sawn deck and floor framing. All five share 18-gauge steel and double-shear nailing, where each joist nail passes through the hanger, the joist, and the hanger again. What separates them is width, height, finish, and pack size: singles for one joist, doubles for two plies, galvanized steel for ordinary framing, ZMAX for treated lumber, and stainless steel for the harshest corrosion.
As an Amazon Associate, we earn from qualifying purchases.
Sections
- Quick Answer
- How to Read the LUS Model Number
- Simpson Strong-Tie LUS26Z ZMAX Joist Hanger, 50-Pack
- Simpson Strong-Tie LUS26-2 Double Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS26 Galvanized Joist Hanger, 100-Pack
- Simpson Strong-Tie LUS28SS Stainless Joist Hanger, 25-Pack
- Simpson Strong-Tie LUS28-2 Double Joist Hanger, 25-Pack
- How to Choose
- Who Should Skip
- Frequently Asked Questions
- Final Verdict
- Product and ASIN Reference
Quick Answer
For most deck and floor framing, the LUS26 galvanized 100-pack covers single 2×6 joists at the lowest effort per connection. Pick the LUS26Z 50-pack for pressure-treated lumber or outdoor frames, the LUS28SS stainless hanger for 2×8 joists near salt air, and the LUS26-2 or LUS28-2 doubles when the joist is two plies thick. Fasteners are sold separately.
How to Read the LUS Model Number
Simpson Strong-Tie packs the whole decision into a short code. LUS marks the family: a face-mount, double-shear hanger for solid-sawn lumber. The first number is the joist depth in inches, so 26 means a 2×6 and 28 means a 2×8. A dash and a second number tells you how many plies the hanger accepts, so LUS26-2 holds two 2×6 plies nailed face to face, while a plain LUS26 holds one. The suffix names the finish: no suffix means standard galvanized steel, Z means the thicker ZMAX coating, and SS means stainless steel.
Width causes the most mistakes. A single hanger measures 1-9/16 inches across the inside of the U, matching one nominal 2x board, while a double hanger measures 3-1/8 inches, matching two plies. Forcing a doubled joist into a single hanger crushes the seat; putting a single joist into a double hanger leaves a gap that lets the joist roll. Finish follows the environment: galvanized steel suits dry interior framing, ZMAX adds a heavier zinc coating for exterior decks and pressure-treated lumber, and stainless steel belongs where corrosion never lets up. Match the fastener metal to the hanger metal, fill every nail hole, and never bend a tab or trim a flange, because the published loads assume the hanger exactly as formed.
Simpson Strong-Tie LUS26Z ZMAX Joist Hanger, 50-Pack
The LUS26Z is the single 2×6 hanger to reach for when the frame lives outside or the lumber is pressure-treated. Its ZMAX finish carries a heavier zinc coating than the standard galvanized version, which matters on a deck ledger, a pergola beam, or any framing that gets rained on and dries out again. The rest is the familiar LUS pattern: 18-gauge steel, speed prongs that hold the hanger while you set the first nails, and double-shear nailing that spreads the load through two points on each joist nail. The 50-pack fits a small to mid-size deck, and the part number is LUS26-50PK.
Specs
- Model LUS26Z; single 2×6 joist; 18-gauge steel with ZMAX finish; 1-9/16 in wide, 4-3/4 in tall, 1-3/4 in bearing length; header fasteners 4 x 10d x 1-1/2 in nails; joist fasteners 4 x 10d nails; double-shear nailing; speed prongs; pack of 50; ASIN B006Q2PX7Q.
Simpson Strong-Tie LUS26-2 Double Joist Hanger, 25-Pack
Doubled joists show up wherever a deck needs a stronger edge, a stair landing, or a beam made from two plies of 2×6. The LUS26-2 is the double version of the standard 2×6 hanger, with a 3-1/8-inch-wide seat that takes both plies at once and a taller 4-7/8-inch profile that gives the doubled member more bearing. Its published loads for Douglas fir and southern pine framing run to about 1,060 lb of uplift resistance and roughly 1,030 lb of download capacity under floor loading. The fastener schedule steps up with the width: header and joist nails are both 0.162 x 3-1/2 in, long enough to pass through both plies and bite the hanger on the far side, which is why ordinary deck screws are not a substitute.
Specs
- Model LUS26-2; double 2×6 joist; 18-gauge galvanized steel; 3-1/8 in wide, 4-7/8 in tall, 2 in bearing length; header fasteners 4 x 0.162 x 3-1/2 in nails; joist fasteners 4 x 0.162 x 3-1/2 in nails; double-shear nailing; speed prongs; pack of 25; ASIN B012GWWFPC.
Simpson Strong-Tie LUS26 Galvanized Joist Hanger, 100-Pack
For a full deck or a floor frame with dozens of identical connections, the LUS26 in the 100-pack is the plain, economical choice. It is the same single 2×6 hanger as the ZMAX version, in standard galvanized steel, with the same 1-9/16-inch seat, 4-3/4-inch height, and double-shear nailing. The difference is finish only, which makes it the pick for interior floor framing, covered porches, and dry locations where the heavier ZMAX coating buys nothing. Published uplift capacity for Douglas fir and southern pine framing is about 1,165 lb, with download capacity around 865 lb under floor loading. Keep the box dry before installation, because surface rust on stored hangers can stain treated lumber.
Specs
- Model LUS26; single 2×6 joist; 18-gauge galvanized steel; 1-9/16 in wide, 4-3/4 in tall, 1-3/4 in bearing length; header fasteners 4 x 0.148 x 3 in nails; joist fasteners 4 x 0.148 x 3 in nails; double-shear nailing; speed prongs; pack of 100; ASIN B012GWUQIU.
Simpson Strong-Tie LUS28SS Stainless Joist Hanger, 25-Pack
The LUS28SS is the hanger for the job where corrosion is the main enemy. Formed from stainless steel for a single 2×8 joist, it stands 6-5/8 inches tall to support more of the deeper member, with a six-nail header pattern that spreads the load across the ledger. Coastal decks, pool decks, and framing that sits in shade and stays damp all benefit from a hanger that will not rust from the inside out. The rule with this hanger is absolute: pair it with stainless fasteners. A stainless hanger fastened with galvanized nails sets up galvanic corrosion at every hole, and the nails will fail long before the hanger does.
Specs
- Model LUS28SS; single 2×8 joist; stainless steel; 1-9/16 in wide, 6-5/8 in tall, 1-3/4 in bearing length; header fasteners 6 x 10d x 1-1/2 in nails; joist fasteners 4 x 10d nails; double-shear nailing; speed prongs; pack of 25; ASIN B00937M25C.
Simpson Strong-Tie LUS28-2 Double Joist Hanger, 25-Pack
The LUS28-2 closes the set as the double hanger for doubled 2×8 members. Its 3-1/8-inch seat takes two plies of 2×8, its 7-inch height gives the deeper joist full support, and its six-nail header pattern carries the heavier loads doubled 2×8 members usually serve: a long deck span, a beam under a stair landing, or a floor opening framed with doubled joists. Published loads for Douglas fir and southern pine framing run to about 1,060 lb of uplift resistance and roughly 1,315 lb of download capacity under floor loading, the highest download figure in this group. The most common mistake is ordering it for a single 2×8: a single joist in a 3-1/8-inch seat will roll under load, and shimming the gap does not restore the engineered connection.
Specs
- Model LUS28-2; double 2×8 joist; 18-gauge galvanized steel; 3-1/8 in wide, 7 in tall, 2 in bearing length; header fasteners 6 x 0.162 x 3-1/2 in nails; joist fasteners 4 x 0.162 x 3-1/2 in nails; double-shear nailing; speed prongs; pack of 25; ASIN B012GWXH1I.
How to Choose
Match the hanger to the lumber first, the environment second, and the pack size last. Measure the joist depth and count the plies before ordering: a single 2×6 takes an LUS26, a doubled 2×6 takes an LUS26-2, a single 2×8 takes an LUS28, and a doubled 2×8 takes an LUS28-2. Check the width with a tape rather than by eye, because a 2×6 and a 2×8 look similar in a dim lumber aisle and the wrong height leaves the joist unsupported or poking above the frame.
Then decide the finish by asking where the frame will live. Interior floors and covered porches are fine with standard galvanized steel. Any deck ledger, any pressure-treated member, and any frame that gets wet regularly deserves ZMAX. Stainless steel is reserved for salt air, pool surroundings, and framing that never fully dries. Once the finish is settled, match the fasteners to it, buy the nails or SD screws in the same metal, and fill every hole. Count every joist end, add a few for mistakes, and pick the box that covers the total: a 25-pack suits one deck, a 50-pack suits a deck plus a landing, and a 100-pack suits a full floor frame or two decks.
Who Should Skip
Skip the LUS family entirely if the framing is engineered lumber rather than solid-sawn boards. I-joists, laminated veneer lumber, and parallel strand lumber need hangers shaped for their thinner flanges and taller profiles, and a solid-sawn hanger will not seat correctly on them. Skip these hangers too if the connection needs a top flange, a concealed flange, or a skewable or slopeable hanger for an angled joist; the LUS is a straight face-mount hanger, and forcing it onto an angled connection loses the engineered load path.
Builders working to a stamped plan should also pause before substituting. If the plans call out a heavier hanger family, a specific model, or a hold-down detail, the LUS is not a drop-in replacement, and the engineer of record should approve any change. The same caution applies to joists carrying unusual loads, such as a rooftop deck or a floor under a large aquarium: the published loads here cover ordinary residential deck and floor framing, and anything beyond that deserves a calculation rather than a catalog pick.
Frequently Asked Questions
Do joist hangers come with nails?
No, none of the five hangers ships with fasteners. Each needs 10d connector nails or the matching SD connector screws, bought separately, in the same metal as the hanger. Standard galvanized hangers take galvanized nails, ZMAX hangers take ZMAX or hot-dip galvanized nails, and the stainless LUS28SS must be paired with stainless fasteners. Fill every nail hole, because the published loads assume a full fastener schedule.
Can I use a single hanger for a doubled joist?
No. A single hanger has a 1-9/16-inch seat for one ply, and a doubled joist needs the 3-1/8-inch seat of a double hanger such as the LUS26-2 or LUS28-2. Squeezing two plies into a single hanger twists the seat and leaves the hanger unable to support the joist evenly. Shimming a single joist into a double hanger is equally wrong, because the gap lets the joist roll.
What is the difference between galvanized, ZMAX, and stainless hangers?
Galvanized steel is the standard finish for dry interior framing and covered structures. ZMAX is a heavier zinc coating for exterior decks, pressure-treated lumber, and framing that gets wet regularly. Stainless steel is for the harshest corrosion conditions, such as coastal air and pool surroundings. The finishes are not interchangeable in one connection, so the fasteners must match the hanger metal to avoid galvanic corrosion.
Can I bend a joist hanger to fit an angled joist?
No. LUS hangers must not be bent, trimmed, or modified, and the published loads apply only to the hanger exactly as formed. An angled or sloped joist needs a skewable or slopeable hanger designed for that geometry, and a top-flange or concealed-flange connection needs a different hanger family. If the angle is slight and the plans allow it, a field-skewable model from the same maker is the correct choice.
Final Verdict
The LUS26 galvanized 100-pack is the default buy for a large run of single 2×6 connections, and the LUS26Z 50-pack is the default for the same joist outdoors or in treated lumber. The LUS28SS earns its place on any coastal or pool-side 2×8 frame, while the LUS26-2 and LUS28-2 cover the doubled members that ordinary single hangers cannot hold. Buy the right width, match the finish to the environment, pair the fasteners to the hanger metal, and fill every hole.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| Simpson Strong-Tie LUS26Z ZMAX Joist Hanger, 50-Pack | B006Q2PX7Q |
| Simpson Strong-Tie LUS26-2 Double Joist Hanger, 25-Pack | B012GWWFPC |
| Simpson Strong-Tie LUS26 Galvanized Joist Hanger, 100-Pack | B012GWUQIU |
| Simpson Strong-Tie LUS28SS Stainless Joist Hanger, 25-Pack | B00937M25C |
| Simpson Strong-Tie LUS28-2 Double Joist Hanger, 25-Pack | B012GWXH1I |
Related guides
Related guides
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!