Updated Nov 20, 2026· 9 min read

Key takeaways

  • Best mortisers for woodworking and precise joinery in 2026: benchtop hollow-chisel machines and a chain mortiser compared, with five proven picks.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

⭐ Key Takeaways
Quick answer: Our top pick is Delta 14-651 Benchtop Mortising Machine, with JET JBM-5 Benchtop Mortiser as a strong alternative.

A mortiser cuts square holes for mortise-and-tenon joints, and it does in seconds what takes a chisel and mallet many minutes. The hollow chisel squares the corners while the auger bit inside it clears the waste, which leaves a clean mortise with flat walls and a flat bottom. A tenon cut to fit that mortise makes a joint that holds for decades without a single screw.

Most mortisers here are benchtop hollow-chisel machines, which suit furniture and cabinet work. One pick is a chain mortiser, which suits timber framing and large joints. This guide compares five mortisers that cover the range a woodworker needs: a compact Delta, a JET benchtop, a Powermatic for heavy work, a Shop Fox with a swiveling base, and a Makita chain mortiser.

As an Amazon Associate, we earn from qualifying purchases.

Sections
  1. Quick Answer
  2. How to Choose a Mortiser for Woodworking and Joinery
  3. Who Should Skip These Mortisers
  4. Frequently Asked Questions
  5. Final Verdict

Quick Answer

For most woodworking, the JET JBM-5 is the best mortiser, since its half-horsepower motor, reversible column, and quick-adjust depth stop cover furniture mortises without taking over the bench. Choose the Delta 14-651 for a small shop, the Powermatic PM701 for heavy daily work, the Shop Fox W1671 for large chisels and angled work, and the Makita 7104L for timber framing.

Delta 14-651 Benchtop Mortising Machine

Delta 14-651 Benchtop Mortising Machine

Delta 14-651 Benchtop Mortising Machine

Check price on Amazon

The Delta 14-651 is the compact pick, with a small footprint and a complete set of chisels in the box. Its half-horsepower motor runs at 1,725 RPM, which is the slow speed that suits mortising: the chisel cuts cleanly without burning the wood, and the auger clears chips without packing the hole. Four chisels come in the box in quarter, five-sixteenths, three-eighths, and half-inch sizes, which covers the common mortise widths for furniture and cabinets.

A rack-and-pinion head moves the chisel smoothly into the work, and an adjustable depth stop sets the mortise depth so every hole in a run matches. A marketplace crawl from seven months ago named the exact model and ASIN. Note that some roundups list this machine at three-quarter horsepower, which is wrong: Delta’s own figure is half a horsepower.

Specs: Model 14-651; 1/2 HP motor; 1,725 RPM; includes 4 chisels, 1/4, 5/16, 3/8, and 1/2 inch; rack-and-pinion head; adjustable depth stop; ASIN: B00006K00N

JET JBM-5 Benchtop Mortiser

JET JBM-5 Benchtop Mortiser

JET JBM-5 Benchtop Mortiser

Check price on Amazon

The JET JBM-5 is the best all-round mortiser here, with a design that fits a working bench rather than a dedicated machine stand. Its half-horsepower motor runs at 1,725 RPM, and the column reverses so the machine can sit against a wall with the handle on either side. A quick-adjust depth stop sets the mortise depth in seconds, and a removable toggle switch keeps the machine safe when the shop is shared. The three-jaw chuck grips the auger bit firmly, and hinged side doors open for bit changes.

At 44 pounds the JBM-5 is light enough to lift onto a shelf when the bench is needed for other work, yet heavy enough to stay put under load. A 4-3/4 inch stroke gives enough travel for deep mortises in thick stock. A tracker page checked in November 2026 named the exact model and ASIN with an Amazon offer and free delivery, plus offers from woodworking suppliers.

Specs: Model JBM-5; 1/2 HP motor; 1,725 RPM; 4-3/4 inch stroke; 44 pounds; reversible column; quick-adjust depth stop; three-jaw chuck; hinged side doors; ASIN: B0000223M4

Powermatic PM701 Benchtop Mortiser

Powermatic PM701 Benchtop Mortiser

Powermatic PM701 Benchtop Mortiser

Check price on Amazon

The Powermatic PM701 is the heavy pick, built for a shop that cuts mortises every day. Its three-quarter-horsepower motor runs at 1,725 RPM, which gives more torque than the half-horsepower machines here and keeps the chisel cutting in dense hardwood. A 5-1/2 inch stroke is the longest in this group, which suits deep mortises in thick legs and rails. At 93 pounds the machine stays planted on the bench, and a double-lock hold-down keeps the workpiece from lifting with the chisel.

A reversible handle suits left and right-handed use, an inline depth stop sets the depth, and a hinged chuck door opens for bit changes. A chisel holder with a sharpening stone sits on the machine, which keeps the chisels honed between jobs. A tracker page checked in November 2026 named the exact model and ASIN with an Amazon offer and free delivery. Note that chisels are sold separately for this machine, so budget for a set. Also note that some roundups list this machine at half a horsepower, which is wrong: Powermatic’s own figure is three-quarter horsepower.

Specs: Model PM701; 3/4 HP motor; 1,725 RPM; 5-1/2 inch stroke; 93 pounds; reversible handle; inline depth stop; double-lock hold-down; chisel holder with sharpening stone; chisels sold separately; ASIN: B000BX1JQU

Shop Fox W1671 Heavy-Duty Mortising Machine

Shop Fox W1671 Heavy-Duty Mortising Machine

Shop Fox W1671 Heavy-Duty Mortising Machine

Check price on Amazon

The Shop Fox W1671 is the pick for large mortises, and its three-quarter-horsepower motor runs at 3,450 RPM, twice the speed of the other benchtop machines here. The higher speed suits the larger chisels this machine takes: three chisels come in the box in half, five-eighths, and three-quarter-inch sizes, which covers the wide mortises used in workbenches, doors, and timber joints. A swiveling base turns the head for angled mortises, and a gas-spring return lifts the chisel smoothly after each cut.

At 90 pounds the machine needs a solid bench and stays where it is put. A manual for this model is hosted under its ASIN, and a forum post links the exact marketplace listing, which confirms the model and ASIN together. No fresh in-stock signal surfaced for this machine, so confirm the listing before ordering.

Specs: Model W1671; 3/4 HP motor; 3,450 RPM; includes 3 chisels, 1/2, 5/8, and 3/4 inch; swiveling base; gas-spring return; 90 pounds; ASIN: B000J0UTL6

Makita 7104L Chain Mortiser

Makita 7104L Chain Mortiser

Makita 7104L Chain Mortiser

Check price on Amazon

The Makita 7104L is the chain mortiser here, and it works on a different principle from the hollow-chisel machines above. A chain with cutting teeth runs around a guide bar, like a small chainsaw, and plunges into the wood to cut a long, clean mortise in one pass. That design suits timber framing, where the mortises are long, deep, and cut into large beams that cannot fit on a benchtop machine. A 10.5 amp motor runs the chain at 3,200 RPM, which gives fast cutting in softwood and hardwood alike.

The tool is handheld, so it goes to the timber rather than the other way round, which matters on a frame-raising job. A tracker page confirmed the model and ASIN, and a marketplace listing in another region confirms the code, though a tracker showed the main listing as unavailable through a fulfillment service, so confirm stock before ordering.

Specs: Model 7104L; chain mortiser; 10.5 amp motor; 3,200 RPM; handheld for timber framing; ASIN: B0002HC2VQ

How to Choose a Mortiser for Woodworking and Joinery

Decide between hollow-chisel and chain first. A hollow-chisel mortiser suits furniture and cabinets, where the mortises are short, square, and cut in boards that fit on a bench. A chain mortiser suits timber framing, where the mortises are long and cut into beams that stay on sawhorses. The two types do not replace each other, so a shop that does both kinds of work needs both kinds of machine.

Look at motor power and speed next. A half-horsepower motor at 1,725 RPM suits furniture mortises in softwood and hardwood, since the slow speed keeps the chisel cool and the torque high. A three-quarter-horsepower motor suits dense hardwood and daily use, since it holds speed under load. A 3,450 RPM machine suits large chisels, since the higher speed clears chips fast, though it can burn the wood if the feed is slow.

Check the stroke length and the chisels in the box. The stroke is how far the chisel travels, and a longer stroke cuts deeper mortises without repositioning the work. A 5-1/2 inch stroke suits thick legs and rails, while a shorter stroke suits cabinet parts. Check which chisel sizes come in the box, since a machine that ships with four chisels costs less to set up than one that ships with none. Standard sizes run from quarter inch to three-quarter inch, and a set that covers that range handles most furniture work.

Consider the table, the fence, and the hold-down. A cast-iron table with a fence keeps the workpiece square to the chisel, which matters when a run of mortises must line up. A hold-down keeps the board from lifting with the chisel on the return stroke, which is the most common cause of a ragged mortise. A depth stop sets the mortise depth so every hole in a run matches, and a reversible column or handle lets the machine sit against a wall in a small shop. Finally, a machine near 90 pounds stays put under load, while a lighter machine needs bolting down.

Who Should Skip These Mortisers

A woodworker who cuts only a few mortises a year can skip a dedicated mortiser, since a drill press with a Forstner bit and a sharp chisel squares the corners well enough for occasional joints. A shop that already owns a router and a mortising jig can cut clean mortises without a new machine, and a loose-tenon joiner covers the same joints with a different method. A chain mortiser is the wrong buy for furniture work, since its long chain cannot cut the short, precise mortises a cabinet needs.

Frequently Asked Questions

What is the difference between a hollow-chisel mortiser and a chain mortiser?

A hollow-chisel mortiser uses a square chisel around an auger bit to cut a square hole in a board on a bench, which suits furniture and cabinets. A chain mortiser uses a cutting chain on a guide bar to plunge a long mortise into a beam, which suits timber framing.

What chisel sizes do I need for furniture mortises?

Quarter, three-eighths, and half-inch chisels cover most furniture work, since tenons in that range suit chair legs, table aprons, and cabinet frames. Larger chisels from five-eighths to three-quarter inch suit workbenches, doors, and timber joints.

Can I cut angled mortises with a benchtop mortiser?

Yes, with a machine that has a swiveling base or a tilting table, which turns the head or the work to the angle needed. A mortiser with a fixed table cuts only square mortises, so check the base before buying when the work includes angled joints.

Do I need a drill press as well as a mortiser?

No, for most furniture work. A mortiser does the whole job: the auger clears the waste and the chisel squares the corners. A drill press with a Forstner bit can rough out a mortise, though the corners still need a chisel by hand. A shop that cuts mortises every week should buy the dedicated machine.

Final Verdict

The JET JBM-5 is the best mortiser for most woodworking, since its half-horsepower motor, reversible column, and quick-adjust depth stop cover furniture mortises without taking over the bench. The Delta 14-651 suits a small shop with its complete chisel set, the Powermatic PM701 suits heavy daily work with its long stroke, the Shop Fox W1671 suits large chisels and angled work, and the Makita 7104L suits timber framing. Match the machine to the joint and check the chisels in the box.

C
Carpenter's Equip Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Mortisers for Woodworking and Precise Joinery 2026Check price on Amazon

Related guides

Browse all Buying Guides guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.